ADHESIVE PENETRATING LUBRICANT
SPECIAL FOR TRANSMISSION CHAINS
LOW OR HIGH SPEED, OPEN DEVICES
EXTREME PRESSURE, ANTI-WEAR
RESISTANT TO THROW-OFF
HYDROFUGE, COMPLETELY RESISTANT TO WATER
DESCRIPTION
Foaming lubricant with a very high viscosity index, having remarkable adherence and penetration properties.
Particularly recommended for the lubrication of all types of chains: roller, long pitch, API type roller-less, hollow rivet, leaf chains and, in general, all open mechanisms with fast or slow movement.
The formulation of this product gives it the property of penetrating to the working surfaces, difficult to access, and reduce their wear.
Perfectly resistant to water, salt water, hot water and steam while providing good anti-corrosion protection.
Product not subject to dripping or throw-off in use.
Extremely neutral and chemically inert. High stability.
Reduces operating noise of roller drive chains, facilitates their mounting.
Regularises the running of toothed chain transmissions, reducing vibration.
To obtain the best possible performance, a chain lubricant must be applied to cleaned and degreased surfaces. Use iBiotec NEUTRALENE V 200 in aerosol, which combines high cleaning and degreasing power along with optimum mechanical action.
Continuous use temperature:
-30°C+140°C
APPLICATIONS
Lubrication of transmission, handling and lifting chains Agricultural chains
Lubrication of open mechanisms, sprockets, gears, pinions and endless screws.
Mechanical components subjected to water spray.
Competition motorcycle chain lubricant.
TYPICAL PHYSICAL-CHEMICAL PROPERTIES
|
PHYSICAL PROPERTIES OF THE LUBRICATING OIL |
||||
|
PROPERTIES |
STANDARD or METHOD |
VALUE |
UNITS |
|
|
Appearance |
visual |
Flowing fluid |
- |
|
|
Colour |
Visual |
amber |
- |
|
|
Scent |
Olfactory |
light |
- |
|
|
Density at 20°C |
NF EN ISO 12.185 |
790 |
g/l |
|
|
Nature of solid lubricants |
- |
Without |
- |
|
|
Nature of base oil |
- |
Polymer |
- |
|
|
Kinematic Viscosity at 40°C at 100°C |
NF EN ISO 3,104 |
1,100 1,000 |
mm2/s-1 mm2/s-1 |
|
|
Sulphated ash |
NF T 60.144 |
0.3 |
% |
|
|
Acid index (ai) |
EN 14,104 |
< 0.2 |
mg(KOH)/g |
|
|
Closed-cup flash point |
NF EN 22.719 |
190 |
°C |
|
|
Self-combustion point |
ASTM E 659 |
> 250 |
°C |
|
|
Freezing point |
ISO 3016 |
-35 |
°C |
|
|
Impurities > 25 µ > 75 µ > 125 µ |
FTMS 791 3005 |
0 0 0 |
number/ml number/ml number/ml |
|
|
PERFORMANCE PROPERTIES |
||||
|
PROPERTIES |
STANDARD or METHOD |
VALUE |
UNITS |
|
|
Utilisation temperature range |
- |
-30 +140 |
°C |
|
|
Copper blade corrosion 24h 100°C |
ISO 2160 |
1a |
value |
|
|
Loss by evaporation 22h at 121°C |
ASTM D 972 |
<-0.5 |
% mass |
|
|
SHELL 4-ball test Impression diameter Weld load index |
ISO 20.623 – ASTM D 2266
|
0.67 3500 |
mm N |
|
|
SRV test |
ASTM D 5707 |
0.14 |
coefficient |
|
|
Elastomer swelling test (dimensional change) |
FTM 791 |
<+0.8 |
% |
|
|
Suppression of operating noise |
FAG MMG 11 |
I |
category |
|
|
Maximum permitted speed |
- |
0.5 |
m/s-1 |
|
|
Water wash-off resistance at 80°C |
ASTM 1264 |
< 1 |
% |
|
|
Cold starting torque at -20°C |
ASTM D 1478-63 |
12 |
N.cm |
|
*nm: not measured or cannot be measured
PRESENTATION
Aerosol 650 ml
|
|
|
Looking for another product?
|
Discover our entire range by clicking on the photo |
Manufacturing, lubrification, cleansing, protection,
IBiotec® Tec Industries® Service
offers a wide range of products reserved for industrial area
If you wish for :
a free sample
a technical advice
a product data sheet
a safety data sheet
IBiotec® Tec Industries®Service
manufacturer of technical chemical products.
Welcome to our website.
IBiotec® Tec Industries®Service is on : 